Parts & Accessories
Boostinators are hub specific conversions designed to take non-boost hubs and convert them to boost compatibility. Don't toss out that wheelset - Boostinate it.
- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Drive Side Axle End Cap
Boostinator kits allow non-boost wheels to be mounted in Boost spacing frames and forks. While incremental, the benefits of the "Boost" 15x110mm front and 12x148mm rear axle standards are clear: better clearance for fatter tires & rims and reduced dish for stiffer, stronger wheels. The big bummer? Taking full advantage requires not only a new frame and fork, but new wheels as well. In response, we have developed the Boostinator. When paired with compatible 15x100mm or 12x142mm hubs, Boostinator kits allow existing wheels to be mounted in Boost-standard frames and forks. Disc and drivetrain positions are maintained and, thanks to a quick re-dish, spoke bracing angles are improved. Boostinator kits consist of a specially-designed axle end cap and, in the case of rear kits, a precision-machined rotor spacer with a set of six high-strength bolts. In keeping with Boost specifications, the disc and cassette are shifted outboard, allowing brakes and derailleurs to function as designed. Compatibility: - Front boostinators are only an endcap and do not require a rotor spacer. The wheel is re-dished. - Rear boostinators require both a re-dish and rotor spacer. - Rear Boostinator kits are not approved for rotors larger than 183mm. - Hubs spacing is 100mm front and 142 rear, and the Boostinators make them 110 and 148 respectively. - Compatible with 6-bolt FRONT wheels and SOME centerlock models. - Compatible with ONLY 6-bolt REAR wheels (there is no way to space centerlock rotors over 6mm). - NOT recommend (or safe) for non-symmetric lacing like the 2:1 lacing found on some of Industry Nine's wheels. *Note: You will need to re-dish your wheel after installing any Boosinator. Boostinator DR: - The Boostinator DR is compatible with DT-Swiss 12x142mm Star Ratchet (240- and 350-series) rear hubs with 6-bolt (IS) rotor mounts. - Centerlock hubs are not supported. - 180- and 190-series hubs are Centerlock only. - The Boostinator DR is also compatible with some complete wheels from DT Swiss, Roval (Specialized), Giant, Syncros (Scott), and others that use DT's Star Ratchet internals. - Remove the disc side end cap. Bearing size 6802 15x24. - Net weight: 18g Boostinator HR: - The Boostinator HR is compatible with 12x142mm Hope Pro 2 EVO and Pro 4 rear hubs. - Non-EVO Pro 2 hubs are not supported - Net weight: 18g Boostinator 9TR: - Compatible with 142x12 rear Industry Nine Torch hubs. - Not compatible with 2:1 lacing wheels from Industry Nine - Not compatible with Centerlock hubs Tech Specs: - Material: 6061 aluminum - Included: Rear kits come with appropriate-length Class 10.9 bolts, each roughly 40% stronger than more common Class 8.8 hardware.
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
$14.95 - $79.95
Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
$11.25 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
$1.50 - $6.25
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually
$8.00 - $16.00
Whisky Parts Co. Tubeless Rim Tape.
- CNC Machined from 6061 T6 aluminum - Knurled body for added grip - Sold as a pair - Upgrade your plastic caps with some style - Weight: So light they will not register on our scale
$16.00 - $18.00
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
DT Swiss tubeless-ready tape seals the rim for tubeless applications and also works well as rim tape for tube-type setups. - Durable adhesive tape works as a rim tape and airseal
Tubeless valves for DT Swiss rims for repair or replacement.
Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Cross Country 29er Tubeless Kit converts standard tubed wheels to tubeless so you can reap the benefits. Everything you need to go tubeless is included. Plus, you won't miss dealing with flat tires and you'll save money on tubes!
SPANK Industries Fratelli Tape is a special ultra-light polyamide, adhesive tubeless conversion tape, which is ideal for SPANK's patented OohBah profile rims. Thicker, less pliable tapes are often difficult or impossible when taping complex rim profiles. Fratelli tape makes tubeless set up simple, and adapts well to a variety of rim types, including sleeved and welded joints. 25mm width tape is suggested for rims up to 29mm internal width, and 30mm tape for rims 30mm internal width and greater. With adhesive properties unaffected in a wide temperature range, Fratelli tape is also perfect for winter riders, or those in exceptionally hot environments. - Material: Ultra Thin Polyamide - Width: 25mm or 30mm - Features: high temperature range adhesive, ideal for complex rim profile Installation: - Affix tape all the way around on the right side snug against the bead hook - Then repeat a second circumference around the left side, providing double-thick coverage over the spoke holes - Use a red-hot awl or similar to pierce the valve hole
Protect your tubes without adding bulk with these Rim Strips from FSA. They're lightweight, and come in different lengths according to wheel size. Peace-of-mind comes standard.
$19.50 - $20.10
DT-Swiss Center Lock Adaptor. Allows 6-bolt rotors to be used on Center Lock hubs. - Rotor thickness between 1.8mm and 2.2mm - Easy assembly and only 29g - Made in Switzerland by DT Swiss - 230mm version accepts all rotors up to 203mm diameter - 160mm version accepts all rotors up to 160mm diameter
- High performance adhesive tape, a great pairing with Velox Cement - Each roll is usually adequate for gluing two tubular tires - Protects tube from spoke/nipple/rim puncture
- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Right Axle End Cap
Page 1 of 1